Savin SF3760NF AE011086 Replacement Tips Upper Hot Roller

Savin SF3760NF AE011086 Replacement Tips Upper Hot Roller

Below you will find the illustrated Savin SF3760NF AE011086 Replacement Tips for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.

Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Savin SF3760NF AE011086

1. Ghosting – Ghosting takes place when the impression or wording on the top or side of the page is discovered later down or across the page faded. This issue ordinarily takes place once toner has gathered on the external coating of the hot roller and causes the hot roller to operate like a printing press, reproducing the image down the sheet. This seems to develop in the middle of the hot roller and is ordinarily easy to identify because of the build up on the surface area is easy to discover.

2. Wrinkling or Creased Paper – This may very well be a number of things but one of them is the hot roller. Toner build up can cause wrinkling paper as the paper adheres to the hot roller and doesn’t feed through regularly. Also, heavy marks in the hot roller coating can result in creases and indents in the paper. This problem often tends to develop when the pick fingers bite into the exterior and with time the devastation piles up and gets progressively worse.

3. Jamming in the fuser – An additional condition that can be caused by a number of factors but typically this is the end result of the previous symtoms not being dealt with when they start to show up and this is the end result when the component seriously breaks down.

The best method to examine the hot roller out is simply to open up the jam removal cover on top of the fuser. You have two rollers within the unit. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Savin SF3760NF AE011086 Replacement Tips Upper Hot Roller

CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray

2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

1. Fusing unit
2. Exit sensor (A) (” × 1)

CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Savin SF3760NF AE011086 Replacement Tips Upper Hot Roller

OK, the Savin SF3760NF AE011086 Replacement Tips job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.

Find additional sources of Copier and Printer Repair Questions Below :

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply