Lanier LD220F AE011086 Installation Tips Upper Hot Roller

Lanier LD220F AE011086 Installation Tips Upper Hot Roller

Below you will find the illustrated Lanier LD220F AE011086 Installation Tips for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.

Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Lanier LD220F AE011086

1. Ghosting – Ghosting occurs when the image or text on the top or side of the page is seen further down or across the page washed out. This issue commonly appears once toner has gathered on the external layer of the hot roller and results in the hot roller to function like a printing press, repeating the impression down the page. This seems to show up in the center of the hot roller and is ordinarily easy to see because of the accumulation on the outside is easy to view.

2. Wrinkling or Creased Paper – This could possibly be a number of things but one of them is the hot roller. Toner build up can contribute to wrinkling paper as the paper sticks to the hot roller and doesn’t feed throughout smoothly. Additionally, penetrating scratches in the hot roller material can cause creases and indents in the pieces of paper. This condition tends to materialize when the pick fingers bite into the coating and gradually the devastation piles up and gets significantly worse.

3. Jamming in the fuser – An additional complication that can be caused by a number of things but commonly this is the end outcome of the above symtoms not being treated when they start to present themselves and this is the end result when the piece essentially breaks down.

The best method to view the hot roller out is simply to open up the jam removal cover on top of the fuser. You have two rollers inside the unit. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Lanier LD220F AE011086 Installation Tips Upper Hot Roller

1. Lanier LD220F FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray

2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Lanier LD220F EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Lanier LD220F AE011086 Installation Tips Upper Hot Roller

OK, the Lanier LD220F AE011086 Installation Tips job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


How to replace Upper Fuser Roller RICOH AFICIO 1013 1013F 120 1515 1515F 1515MF MP161 MP161F MP161SPF MP171 MP171F MP171SPF MP201F ...

Find additional sources of Copier and Printer Repair Questions Below :

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply