Lanier LD015F AE011086 Installation Tips Upper Hot Roller

Lanier LD015F AE011086 Installation Tips Upper Hot Roller

Below you will find the illustrated Lanier LD015F AE011086 Installation Tips for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.

Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Lanier LD015F AE011086

1. Ghosting – Ghosting happens when the image or wording on the top or side of the sheet is found further down or across the page faded. This event ordinarily happens when toner has gathered on the external layer of the hot roller and can cause the hot roller to operate like a printing press, repeating the image down the page. This is inclined to show up in the middle section of the hot roller and is typically easy to see because of the build up on the outside is easy to notice.

2. Wrinkling or Creased Paper – This could possibly be a number of things but one of them is the hot roller. Toner build up can result in wrinkling paper as the paper adheres to the hot roller and doesn’t feed thru uniformly. In addition, deep scratches in the hot roller surface area can cause creases and indents in the paper. This event often tends to develop in the event that the pick fingers bite into the coating and eventually the devastation piles up and gets significantly worse.

3. Jamming in the fuser – Yet another issue that can be caused by a variety of factors but typically this is the end result of the above symtoms not being dealt with when they start to arise and this is the end result when the component seriously breaks down.

The easiest method to inspect the hot roller out is just to open up the jam removal cover on top of the fuser. You have two rollers within the unit. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Lanier LD015F AE011086 Installation Tips Upper Hot Roller

1. Lanier LD015F FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray

2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Lanier LD015F EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Lanier LD015F AE011086 Installation Tips Upper Hot Roller

OK, the Lanier LD015F AE011086 Installation Tips job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


How to replace Upper Fuser Roller RICOH AFICIO 1013 1013F 120 1515 1515F 1515MF MP161 MP161F MP161SPF MP171 MP171F MP171SPF MP201F ...

Find additional sources of Copier and Printer Repair Questions Below :

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply