Gestetner F104L AE011086 Replacement Tips Upper Hot Roller

Gestetner F104L AE011086 Replacement Tips Upper Hot Roller

Below you will find the illustrated Gestetner F104L AE011086 Replacement Tips for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.

Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Gestetner F104L AE011086

1. Ghosting – Ghosting develops when the impression or text on the top or side of the sheet is noticed further down or across the page washed out. This situation commonly comes about once toner has amassed on the surface layer of the hot roller and causes the hot roller to function like a printing press, duplicating the impression down the page. This is inclined to materialize in the center of the hot roller and is traditionally easy to see because of the build up on the surface area is easy to view.

2. Wrinkling or Creased Paper – This could possibly be a number of things but one of them is the hot roller. Toner debris can induce wrinkling paper as the paper sticks to the hot roller and doesn’t feed throughout evenly. Likewise, deep scrapes in the hot roller exterior may cause creases and indents in the document. This situation usually tends to come about in the event that the pick fingers bite into the exterior and with time the devastation piles up and gets significantly worse.

3. Jamming in the fuser – An additional complication that can be caused by a variety of things but ordinarily this is the end outcome of the stated above symtoms not being treated when they start to appear and this is the end result when the component absolutely breaks down.

The easiest way to inspect the hot roller out is simply to open up the jam removal cover on top of the fuser. You have two rollers inside the unit. One is rubber and spongy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Gestetner F104L AE011086 Replacement Tips Upper Hot Roller

1. Gestetner F104L FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray

2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Gestetner F104L EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Gestetner F104L HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Gestetner F104L AE011086 Replacement Tips Upper Hot Roller

OK, the Gestetner F104L AE011086 Replacement Tips job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


How to replace Upper Fuser Roller RICOH AFICIO 1013 1013F 120 1515 1515F 1515MF MP161 MP161F MP161SPF MP171 MP171F MP171SPF MP201F ...

Find additional sources of Copier and Printer Repair Questions Below :

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply