Gestetner DSM416PF AE011086 Installation Diagrams Upper Hot Roller

Gestetner DSM416PF AE011086 Installation Diagrams Upper Hot Roller

Below you will find the illustrated Gestetner DSM416PF AE011086 Installation Diagrams for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.


Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Gestetner DSM416PF AE011086

1. Ghosting – Ghosting develops when the image or wording on the top or side of the sheet is observed later down or across the page faded. This condition generally crops up when toner has gathered on the surface layer of the hot roller and causes the hot roller to operate like a printing press, replicating the image down the page. This often tends to occur in the center of the hot roller and is typically easy to identify because of the build up on the surface is easy to notice.

2. Wrinkling or Creased Paper – This could be a number of things but one of them is the hot roller. Toner debris can bring about wrinkling paper as the paper adheres to the hot roller and does not feed through equally. Likewise, deep scrapes in the hot roller layer can result in creases and indents in the pieces of paper. This situation is likely to materialize in the event that the pick fingers bite into the coating and as time passes the deterioration piles up and gets progressively worse.

3. Jamming in the fuser – One more condition that can be caused by several factors but usually this is the end result of the previous symtoms not being attended to when they start to show up and this is the end result when the element really breaks down.

The best method to examine the hot roller out is just to open up the jam removal cover on top of the fuser. You have two rollers throughout the component. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Gestetner DSM416PF AE011086 Installation Diagrams Upper Hot Roller

1. Gestetner DSM416PF FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray


2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Gestetner DSM416PF EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

3-4. Gestetner DSM416PF HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Gestetner DSM416PF HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Gestetner DSM416PF AE011086 Installation Diagrams Upper Hot Roller

OK, the Gestetner DSM416PF AE011086 Installation Diagrams job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


RICOH AFICIO MP161 MP171 MP201 UPPER FUSER ROLLER

How to replace Upper Fuser Roller RICOH AFICIO 1013 1013F 120 1515 1515F 1515MF MP161 MP161F MP161SPF MP171 MP171F MP171SPF MP201F ...

Find additional sources of Copier and Printer Repair Questions Below :
Fixya.com

Fixyourownprinter.com

helpowl.com

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply