Nashuatec D1205 PMB12990K Installation Advice Fuser PM Kit

Nashuatec D1205 PMB12990K Installation Advice Fuser PM Kit

Nashuatec D1205 PMB12990K Installation Advice Fuser PM Kit – Okay, these units are undoubtedly old. I know I identified them an episode of Ancient Aliens a few days ago. The great news is that they’re impressive devices and of course if your supervisor is Mr. Scrooge you very well may need to keep it operating a little longer. Down the page you will notice the illustrated instructions in addition to links to order your PM kit if necessary.


Rated at 90K this PM kit restores the regular wear pieces in the fuser and transfer roller area. Most the problems I see with these fusers are ghosting issues and jamming as toner gets built up over the hot roller or pressure roller. Pick fingers are another problem I look for with them. Either absent or cracked pick fingers can lead to jamming troubles. Additionally, build up of toner over time might scratch the surface of the hot roller and wear away the surface of the roller.

Nashuatec D1205 PMB12990K Installation Advice Fuser PM Kit

Mention: I have bundled a few other units than this maintenance kit was built for. The Hot Roller, Pressure Roller, Transfer Roller, and Discharge Plate ought to be universal for these units. However, the strip or pick fingers, whatever you want to call them, aren’t compatible on all models. They should work on the newer models however they probably won’t operate on older models. In case you’re lacking some pick fingers or if they appear fairly bad on the machine your repairing you may need to double check the part numbers on them.

1. Nashuatec D1205 FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray


2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Nashuatec D1205 EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

3-4. Nashuatec D1205 HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Nashuatec D1205 HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

7. Nashuatec D1205 THERMO-SWITCH AND THERMISTOR
1. Hot roller assembly
2. Thermo-switches (A)(B) (! x 2 for each)
3. Thermistor (C) (! x 1)
Reassembling : Make sure the following:
• The thermistor is in contact with the hot roller.
• The hot roller turns smoothly.

8-9. Nashuatec D1205 PRESSURE ROLLER
1. Separate the fusing unit into two sections
2. Fusing entrance guide (A)
3. 2 springs (B)(C)
4. 2 pressure arms (D)(E)
5. Bushing (F)
6. Pressure roller (G)

OK, the Nashuatec D1205 PMB12990K Installation Advice job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


Replacement Fuser Roller RICOH MP161 MP171 MP201 Lanier LD117 LD220

Piec FUSER UNIT Ricoh Aficio MP171 MP171F MP171SPF MP201SPF wymiana wałków, separatorów, lamp, łożysk, odrywaczy Ricoh Aficio MP171 Ricoh ...

Find additional sources of Copier and Printer Repair Questions Below :
Fixya.com

Fixyourownprinter.com

helpowl.com

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply