Savin 920F AE011086 Replacement Advice Upper Hot Roller

Savin 920F AE011086 Replacement Advice Upper Hot Roller

Below you will find the illustrated Savin 920F AE011086 Replacement Advice for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.


Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Savin 920F AE011086

1. Ghosting – Ghosting takes place when the image or text on the top or side of the sheet is noticed later down or across the page washed out. This event generally crops up once toner has collected on the surface layer of the hot roller and can cause the hot roller to operate like a printing press, duplicating the image down the page. This usually tends to happen in the middle of the hot roller and is ordinarily easy to identify because of the build up on the surface area is easy to see.

2. Wrinkling or Creased Paper – This could possibly be a number of things but one of them is the hot roller. Toner debris can bring about wrinkling paper as the paper sticks to the hot roller and doesn’t feed through uniformly. Likewise, heavy marks in the hot roller layer can result in creases and indents in the document. This scenario usually tends to materialize in the event that the pick fingers bite into the layer and as time passes the devastation piles up and gets increasingly worse.

3. Jamming in the fuser – An additional problem that can be caused by a number of factors but generally this is the end result of the stated above symtoms not being addressed when they start to surface and this is the end result when the part essentially breaks down.

The fastest way to view the hot roller out is simply to open up the jam removal cover on top of the fuser. You have two rollers throughout the component. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Savin 920F AE011086 Replacement Advice Upper Hot Roller

1. Savin 920F FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray


2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Savin 920F EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

3-4. Savin 920F HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Savin 920F HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Savin 920F AE011086 Replacement Advice Upper Hot Roller

OK, the Savin 920F AE011086 Replacement Advice job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


Replacement Fuser Roller RICOH MP161 MP171 MP201 Lanier LD117 LD220

Piec FUSER UNIT Ricoh Aficio MP171 MP171F MP171SPF MP201SPF wymiana wałków, separatorów, lamp, łożysk, odrywaczy Ricoh Aficio MP171 Ricoh ...

Find additional sources of Copier and Printer Repair Questions Below :
Fixya.com

Fixyourownprinter.com

helpowl.com

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply