Savin 816F AE01-1086 Installation Instructions Upper Hot Roller

Savin 816F AE01-1086 Installation Instructions Upper Hot Roller

Below you will find the illustrated Savin 816F AE01-1086 Installation Instructions for the Upper Hot Roller. Also, you will find links to order in a replacement hot roller if you decide it’s time to get one on order. Now, if you want to perform the whole PM on the fuser then find the article under this machine to get the information about that repair.


Compatible Part Numbers : AE01-1086, AE01-1061, C2114-7780, AE011086, AE011061

Reasons to replace the Savin 816F AE01-1086

1. Ghosting – Ghosting occurs when the impression or wording on the top or side of the sheet is viewed further down or across the page diminished. This situation ordinarily takes place when toner has collected on the surface shell of the hot roller and may cause the hot roller to work like a printing press, duplicating the impression down the sheet. This tends to show up in the middle of the hot roller and is ordinarily easy to tell because of the accumulation on the outside is easy to observe.

2. Wrinkling or Creased Paper – This might be a number of things but one of them is the hot roller. Toner build up can lead to wrinkling paper as the paper sticks to the hot roller and doesn’t feed throughout regularly. Furthermore, profound scratches in the hot roller surface area can lead to creases and indents in the pieces of paper. This scenario tends to materialize when the pick fingers bite into the covering and after some time the destruction piles up and gets increasingly worse.

3. Jamming in the fuser – An additional problem that can be caused by numerous factors but usually this is the end result of the above symtoms not being treated when they start to appear and this is the end result when the element absolutely breaks down.

The fastest way to check the hot roller out is simply to open up the jam removal cover on top of the fuser. You have two rollers within the unit. One is rubber and mushy, the pressure roller, and the other is hard and made out of metal, the hot roller. Open it up and look for scratches on the surface, build up of toner, or discolorization.

Savin 816F AE01-1086 Installation Instructions Upper Hot Roller

1. Savin 816F FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray


2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Savin 816F EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

3-4. Savin 816F HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Savin 816F HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

We can stop here because we aren’t replacing the other parts. Now if you do decide you need to replace the other parts then check out the fuser PM kit article for this machine.

Savin 816F AE01-1086 Installation Instructions Upper Hot Roller

OK, the Savin 816F AE01-1086 Installation Instructions job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


RICOH AFICIO MP161 MP171 MP201 UPPER FUSER ROLLER

How to replace Upper Fuser Roller RICOH AFICIO 1013 1013F 120 1515 1515F 1515MF MP161 MP161F MP161SPF MP171 MP171F MP171SPF MP201F ...

Find additional sources of Copier and Printer Repair Questions Below :
Fixya.com

Fixyourownprinter.com

helpowl.com

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply