Savin 2513 PMB12990K Replacement Instructions Fuser PM Kit

Savin 2513 PMB12990K Replacement Instructions Fuser PM Kit

Savin 2513 PMB12990K Replacement Instructions Fuser PM Kit – Okay, these models are outdated. I believe I identified them an episode of Ancient Aliens a few days ago. The great thing is that they are fantastic devices and if your supervisor is Mr. Scrooge then you might need to keep it operating a little longer. Beneath you will discover the illustrated instructions alongside links to order your PM kit if required.


Rated at 90K this PM kit changes the regular wear pieces in the fuser and transfer roller area. Most the issues I see with these fusers are ghosting issues and jamming as toner gets built up along the hot roller or pressure roller. Pick fingers are another issue I come across with these. Either lost or busted pick fingers can lead to jamming problems. Also, build up of toner after some time can scratch the surface of the hot roller and wear away the surface of the roller.

Savin 2513 PMB12990K Replacement Instructions Fuser PM Kit

Notice: I’ve covered a number of devices than this maintenance kit was designed for. The Hot Roller, Pressure Roller, Transfer Roller, and Discharge Plate should all be common for these units. However, the strip or pick fingers, whatever you want to call them, aren’t compatible on all models. They will likely work on the newer models however they might not operate on older models. So if you’re lacking some pick fingers or if they appear fairly bad on the machine your working on you might want to double check the part numbers on them.

1. Savin 2513 FUSING UNIT
CAUTION : Before handling the fusing unit, make sure that the unit is cool enough. The fusing unit can be very hot.
1. Copy tray


2. Open the right door.
3. Connector cover (A) (! x 1)
NOTE: When reinstalling, attach the ground wire.
4. Fusing unit (B) (! x 2, ” x 4)

2. Savin 2513 EXIT SENSOR
1. Fusing unit
2. Exit sensor (A) (” × 1)

3-4. Savin 2513 HOT ROLLER STRIPPER PAWLS
CAUTION: Do not damage the hot roller stripper pawls and the tension springs.
1. Fusing unit
2. Separate the fusing unit into two sections: the hot roller section (A) and the pressure roller section (B)
NOTE: After removing the screws, lower the pressure roller section about halfway and then slide it toward the front side to detach it.
3. Support rollers (C)
4. Hot roller stripper pawls (D)
NOTE: Remove the spacer (E) if you are removing the hot roller assembly

5-6. Savin 2513 HOT ROLLER & FUSING LAMP
CAUTION: Do not touch the fusing lamp and rollers with your bare hands.
1. Hot roller stripper pawls and spacers
2. Hot roller assembly (A) (! x 2)
3. Fusing lamp (B)
NOTE: When reassembling, check that the direction of the fusing lamp is correct (C)(D).
4. Hot roller (C) (2 C-rings, 1 spacer, 1 gear, 2 bushings, 1 cover (D))
Reassembling Use caution:
• The fusing lamp is positioned correctly.
• The fusing lamp does not touch the internal part of the hot roller.
Also, make sure you put the fuser bushings on the right direction. I just worked on a machine that somebody else had rebuilt the fuser and it was making a horrible screeching noise because the previous tech had put the bushings on backwards.

7. Savin 2513 THERMO-SWITCH AND THERMISTOR
1. Hot roller assembly
2. Thermo-switches (A)(B) (! x 2 for each)
3. Thermistor (C) (! x 1)
Reassembling : Make sure the following:
• The thermistor is in contact with the hot roller.
• The hot roller turns smoothly.

8-9. Savin 2513 PRESSURE ROLLER
1. Separate the fusing unit into two sections
2. Fusing entrance guide (A)
3. 2 springs (B)(C)
4. 2 pressure arms (D)(E)
5. Bushing (F)
6. Pressure roller (G)

OK, the Savin 2513 PMB12990K Replacement Instructions job is not the easiest thing to do in the world but there are worst repairs I have done. The main thing is to take your time and follow the instructions.


Find additional sources of Copier and Printer Repair Questions Below :
Fixya.com

Fixyourownprinter.com

helpowl.com

copytechnet - Warning - This site is for people with some knowledge of how machines work. You need to try what the service manual says to do before you ask questions. Also, if it's obvious you don't know what you are talking about they aren't afraid to tell you to stop wasting their time.

We will be happy to hear your thoughts

Leave a reply